Skip to main content
#
 
cart
our twitterour facebook page pintrest youtube
Latest Posts
Archive
Categories

 Nuggets of News Blog 

Sunday, July 14 2019

Alluvial gold refers to tiny gold flakes that come to be through water erosion and movement. In geology, alluvium alluvial goldis loose sediment which has been eroded from a primary source, transported and further eroded by water, and redeposited. Since gold is extremely dense, it is easily trapped alongside other dense alluvial particles. The bits of gold found in these deposits of alluvium are called “alluvial gold.”

The alluvial environment is a very complex one, with many natural forces competing with each other. The forces that lay down gold are a summation of many flood water events of varying intensity that cause the reworking of sands and gravels. Between major flood events, water naturally flows along the already created path and typically the gold present in the gravel or on the surface will not move much. But the larger flooding events can change the drainage routes and even the river’s shape. Some curves can be shut off from the stream and bypassed.  Where the water speed decreases, gravels will drop out of suspension, creating alluvial pay streaks that are typically located along and near the riverbed.

To identify where a pay streak might be located, take the flow of the waterway into consideration. The most productive streaks are formed as a result of major floods that are significant in terms of both water flow and intensity of erosion. Greater amounts of gold are present here as compared to regular gravels. Pay streaks tend to possess a comet-like form. At the “head” or “heart”  is found the richest concentration of gold. At this location, the gravel is coarser and the sandy and silty fraction is much less. This little bit of silt is present only for a few centimeters on the surface, laid down in the last phases of the flood as the silt is dropped. The gold in these gravels is typically small flat flakes, with maybe a small picker or two.

As gold prospectors, our objective is to learn to read a stream and recognize the pay streaks it contains. Think about where you are going to dig before you start and then repeatedly test the gravel you are processing. It is important to consider the presence, form, and depth of the bedrock on which the water and all the alluvial gravel deposits are sitting. In many cases, the gold will naturally concentrate in the lowest part of the riverbed, making a gold-rich path. During high water events, much of the gold is picked up and put back into motion, which leads to forming new pay streaks. Some will be laid back down along the low line of the stream, but may also end up a little farther downstream. The gravels in contact with the bedrock or false bedrock base are often the richest. The same facts apply to the alluvial pay streaks that are formed on gravel bars— the lowest level of the gold-bearing gravel is normally the richest.

The alluvial environment changes over time. Alluvial pay streaks generated 100 years ago could become buried, then subsequently be eroded and exposed again. The erosion might be in part or in total, generating a new series of paystreaks further downstream. Pay particular attention to large boulders and trees. Obstacles like these may partially block the water flow and provide an opportunity for increased gold concentrations, especially behind the obstructions. If there are fissures, holes or natural traps in the stream, be sure to sample these areas, too.

Although high water events are sporadic, when you do find a paystreak caused by one, it can be a very productive spot. Stick with it and keep in mind most are small and narrow and best worked by hand with a sluice and gold pans. 

Nugget of News Blog

Posted by: Denise AT 08:09 am   |  Permalink   |  Email
Tuesday, March 26 2019

For nearly a decade, those of us who admit to watching TV reality shows related to gold mining have been gold rushenlightened and entertained by Gold Rush, White Water, Bering Sea Gold, Under the Ice, Jungle Gold, and others. And the once-ordinary people we’ve gotten to know from these shows— Todd Hoffman, Parker Schnabel, Rick Ness, Tony Beets, Dakota Fred, Emily Riedel, Shawn Pomrenke to name just a few — became celebrities practically over night. In fact, Gold Rush remains the most-watched Friday night program in all of US television among males aged 18 to 49 and women aged 25 to 54! 

With so much scenic footage of places like Scribner Creek, Eureka Creek, and the Bering Sea, it can almost feel like you’ve been there even though the probability of going to Yukon or Nome is as remote as the actual locations. Reality television is a compelling and very influential form of entertainment. It shows real people, real experiences (with some “Hollywood” thrown in) and we somehow relate to them, especially to the “stars” you either love or love to hate. The challenges of inter-miner-relationships that unfold in front of the viewing public can remind you of your own family dynamics, too. But do you actually LEARN anything VALUABLE about gold mining by tuning in?

Beyond the entertainment value, the answer is yes! Whether gold mining is the way you make your living or more of a hobby, there are many similarities between small scale and large scale operations. Let’s say you go prospecting every Saturday during the summer and have a few nice pieces of equipment and accessories that you haul in your truck. Whether you head for public land or a private claim, you know there are no guarantees. You do some research, set up your sluice, shovel the dirt, put in the hours, but some days you just don’t find gold, or perhaps not enough to pay for your gas and other expenses. Parker and Tony and Rick and other reality show stars are pretty much doing the same, except on a larger scale. Instead of a shovel, they use a D10 dozer. We see their big machines constantly breaking down and the bush-fixes they come up with (who knew eggs could help plug a radiator leak!). In comparison, you’ve probably struggled with the pitch on your highbanker, and had to rely on duct tape a time or two! Instead of a Gold Cube or spiral panner, these TV mine bosses use huge shaker tables to recover their gold. Instead of several hours, they wait several days to do a clean-up and are often still disappointed in the results. In other episodes they're elated and cheering at their success, just like we all do when we find a gold nugget!  

Perhaps one important lesson we can take away from these TV shows is about pivoting. If the ground or stream you’re working doesn’t produce, despite the time and trouble you’ve already invested, re-think your strategy. Maybe you’ll have 10 different ideas or locations, but only one of them will really work. That’s OK. Be willing to change your technique or the matting in the bottom of the sluice or try a different piece of equipment than what you’d normally use. Gold mining is a challenge, but as long as you’re reasonable with your expenditures and your expectations, it’s a heck of a lot of fun in the great outdoors. And it also gets you off the couch… just remember to record those reality shows so you can watch them at a later date when you’re not out in the gold fields "making it happening" as Tony Beets likes to say!  Good luck!

Nugget of News Blog

Posted by: Denise AT 06:34 pm   |  Permalink   |  Email
Friday, February 01 2019
Did you know... there is actually more gold still out there waiting to be found today than the old-timers ever gold showrecovered way back in the 1800s gold rush era? And did you also know that attending a GPAA Gold and Treasure Show (Gold Prospector's Association of America) is a great place to get started on your modern day treasure hunt?!
Browse the show floor to find dozens of leading worldwide manufactures and local vendors demonstrating the latest and greatest gold mining and metal detecting equipment, attend free seminars, ask questions of the pros, and enter to win thousands of dollars in door prizes. Pick up a pan for the first time or hone your skills at the panning zone, where skilled instructors will help you recover gold, for free. Keep all the gold you find! 
Saturday show hours 10 am - 5 pm and Sundays 10 am - 4 pm in these cities:
  • Phoenix, AZ: March 2-3, Arizona Expo & State Fair
  • Fresno, CA: March 9-10, Fresno State Fairgrounds
  • Puyallup, WA: March 23-24, Washington State Fair Events Center
  • Portland, OR: March 30-31, Portland Expo Center
  • Denver, CO: April 13-14, National Western Complex
  • Ft Worth, TX: May 4-5, Will Rogers Memorial Center
Visit the GPAA website for more details and to buy your $5 adult tickets; kids 12 and under plus military and veterans with ID are FREE.  If you can, make a family road trip out of attending one or more of the  shows this spring. In addition to the show itself, each city has fun touristy things to do, and if you're a GPAA member, you can visit nearby mining claims.
Whether you’re a family with kids or a lone enthusiast, a GPAA Gold & Treasure Show is your one-stop-shop for all of your gold prospecting and treasure hunting wants and needs. By attending a show, you're sure to have a blast, meet interesting people, find new tools, and learn new tricks of the trade. All of that is enough to make you hollar Eureka!
Nugget of News Blog
Posted by: Denise AT 06:00 am   |  Permalink   |  Email
Sunday, December 30 2018

When prospecting an area that’s known for gold, put yourself in the boots of the old-timers who came before togold indicators help you decide where to begin. Look at your site from all directions and think about what they could and could not do way back then. Your modern-day equipment and knowledge are a lot more advanced than what they had to work with, so you’re already a step ahead! Many times miners jumped in with both feet and started mining to beat the other guys. But being in a hurry meant they could have missed a lot, or moved on too quickly from their original discovery before it was completely worked out. Considering the lay of the land will reveal important clues that can help you better formulate a plan when you're out in the field. Here’s what to look for:

Host rock (or bedrock) could be shale, diorite, granite, quartz, clay or other material. Keep an eye out for changes in the area’s host rock and notice the direction in which it’s running.

Contact zones occur when a rock or mineral cuts or crosses the host rock. Generally, gold is deposited along contact zones, which can be a few inches or several hundred feet wide. If bedrock in your area runs north to south and you notice a color change in material that runs east to west, you’ve found a contact zone.

Outcroppings are a lump of high ground with weather-worn rocks which are generally rounded and usually situated on ridges, but can be located anywhere. Especially look for iron staining on outcroppings.

Ditch lines of yesteryear were generally dug into and run along somewhat level ground. Very close to diggings, especially in hilly or steep terrain, they may have been cut loose to wash downhill.  Follow the old water ditches and see where they end up.

Exploratory trenches were not used for water but most of the time were deeper and would often circumnavigate a rich area that may be throwing gold from clay lines, pockets, quartz seams and any other local contacts. Trenches were dug simply to expose any contacts that may be present. As a contact was crossed, old-timers checked it out in both directions for values.

Rock cairns are piles of rock or stone used for claim corners. Standing high on a slope looking down is a great vantage point from which to spot cairns and other man-made landmarks. By locating a historic claim, you definitely have a great place to begin! 

Posted by: Denise AT 12:31 pm   |  Permalink   |  Email
Monday, October 01 2018

A highbanker, sometimes called a power sluice, is a very flexible and efficient piece of equipment when you’re gold mining in areas with a good amount of water. Their main use is to allow you to pump the water to the gravels rather than carrying heavy buckets of gravel to the water. The optimal place to use a high banker is a location along a river where there are lots of bench gravels that have been lefthighbanker high and dry by erosion. Just shovel material directly into a high banker and let the equipment do the rest of the work! As long as there is sufficient water close by so the hose can reach it, you’ll be good to go. High bankers are available in various sizes. The bigger the unit, the more gravel it will handle in a day. That also means it will likely be heavier and less portable. High bankers are fairly simple to set up and operate. They have three main components: a hopper feed box, and sluice box, and a pump.

Hopper: The feed box contains a grizzly screen with a water spray bar. The water is normally sprayed from simple plastic pipes with a series of small holes drilled into them. A water valve located ahead of the spray pipe controls the amount of water flow going into the feed box sprays. A series of rods are arranged to make a slat-type screen (called a grizzly) that allows water and smaller material to fall through and go down into the sluice box. The large rocks that are caught by the grizzly are washed with the spray and then rejected. The slats should be set on an angle so that most of the larger gravel will slide off the slats by the pull of gravity without you needing to push them off by hand. Some rocks may hang up, but for the most part, they will slide off on their own. The spray water comes out under a lot of pressure and washes any loose sand or clay into the sluice and also provides part of the water needed to move material through the sluicebox area.

Sluice: High bankers utilize a normal sluice to recover the gold from the gravels, and the operation of the sluice box portion of a high banker is basically the same as that of a hand or stream sluice. With a highbanker, the water is supplied by a pump rather than the flowing water of a stream. The matting and miners moss underneath the sluice’s riffles are the same. Gold flakes get caught in the riffles and moss the very same way as it does in a hand sluice.  A nice back-saving bonus on a high banker is that it will be on legs, so you can operate it on any terrain. A normal hand sluice lays on the bottom of a streambed.

Pump: The centrifugal type pump should be set near the water as it is more efficient to pump water uphill to the sluice than to suck it up to the pump. This is only important where there is a lot of vertical distance between the pump and the sluice. If there is less than 10 feet of vertical distance, it does not matter much. Pumps can be set up quite a distance away horizontally from the sluice. It will work so long as there is sufficient water at the source where the pump is located. Vertical distance is more of a problem than horizontal distance; 30-40 feet is the maximum vertical climb for most pumps. The standard lay flat type of hose is used to carry the water up to the feed hopper. Be sure to have enough hose and some extra in case you spring a leak! Remember to position the pump so that you aren’t breathing motor exhaust fumes all day!

The big advantage of a highbanker is working materials that are found in a location away from a river, like benches and other isolated patches of gravel. Moving the water to the sluice with a pump saves you from carrying the material down to the stream.  The only disadvantage to highbanking for gold might be that it’s more equipment to pack around than just your usual digging equipment. It would be wise to test your ground before hauling in your high banker. Testing will indicate if there is enough gold in the gravels to warrant bringing in more than a hand sluice. If you have at least an amount of gravel that represents a full day of digging and sluicing, bring in a highbanker.

The adjustment of a high banker is much less than the steep slope you usually would use with a hand sluice. Adjust the water flow to the minimum flow rate that it takes to get all the rocks that fall through the screen to keep moving down the sluice box section. If rocks or gravel hang up and bury the sluice, you need more water and perhaps a steeper box angle to wash that stuff away. The height of the feed box is another important adjustment. You want it low to allow you an ease of feeding in the material. If too high, you will hurt your back lifting heavy shovels full of gravel. Too low and you may be constantly sweeping away tailings at the back of the sluice.

The feed box itself should be adjusted to ensure the angle of the slat screen rods (the grizzly) allow the gravel to be well washed before it moves out as waste. This is because a lot of small gold adheres too the larger cobbles. If rocks and cobbles just roll through without getting a thorough washing, you will be losing gold. The rejection of the large oversize rocks is important as it lets your sluice to a better job. If those bigger rocks make it into the sluice, you’ll be getting much worse recovery of fine gold.

Be sure the foot valve or strainer on the intake hose is clear and able to deliver a full water flow. Sometimes the foot valve can get clogged with leaves or other debris. A blocked or partially obstructed foot-valve won’t allow the high banker to operate properly. For environmental reasons, it is a good idea to have your water drain into a pond or pit that is not directly connected to the stream. This is so that the clay and mud can settle out, otherwise make sure there are no legal issues of putting that mud back into a flowing stream.

Some models of highbankers can also be run as a dredge. These highbanker/dredge combos can save you money, offer flexibility, but are also a bit of a compromise since the dredge portion is generally small. Combo units will be equipped with a suction nozzle type of intake. This design is best for working small shallow streams and tributaries.  These systems are designed to be set up alongside the stream edge and have adjustable legs rather than float systems that you’d normally see on a larger suction dredge. With a suction nozzle and more hoses, the combo unit will operate as a suction dredge, picking up material from underwater crevices  and delivering it to the sluice. Highbanker/dredge combos also can be ideal for working in and around ponds in old hydraulic mining pits.

The next time you are out in the field, consider if a highbanker or power sluice can help you get more gold. To determine if the answer is yes, ask yourself these questions:  Where is the nearest water? Can I shovel directly from the diggings into the feed hopper? Can I set it up to allow gravity to do a lot of the tailings clearing work? Where will the pump go? With a little thought and planning, you’ll be able to decide if highbanking for gold will increase your productivity. In most cases it will. Move more dirt, get more gold!  Good luck!

Posted by: Denise AT 01:00 am   |  Permalink   |  Email
Monday, August 06 2018

Back to School promo!  Limited time only— combo price ends August 18, 2018!  Each Teknetics T2 metal detector is now shipping with stereo headphones and a digger recovery tool. ALL FOR $499 with FREE SHIPPING!  Buy now using coupon code A1486.

Teknetics T2The T2 is a high-performance multi-purpose professional grade metal detector. This detector set the benchmark in advanced electronic technology and functional design in the metal detector market. Its legendary performance coupled with its light weight and perfect balance make the T2 the best metal detector in its price range.

The T2 excels at coins-shooting, relic hunting and gold prospecting.

  • Large LCD Screen with 0-99 Numeric Target ID
  • Straightforward Menu-Driven User Interface
  • Trigger Actuated Target Pinpointing with variable audio pitch
  • Double Filter Discrimination Modes For Searching In Trashy Areas
  • Trigger Actuated FASTGRAB™ Instant Ground Canceling with manual override
  • Manual Ground Cancellation Option
  • Continuous Ground Monitor - Ground Mineralization Bar Graph Readout
  • Waterproof 11-inch Open Frame Bi-Axial™ Searchcoil Great for Highly Mineralized Soils.
  • Renowned Target Separation Capability Detects targets at extreme depths
  • Low Operating Cost - More than 40 hrs. with 4-AA Batteries (not included)

Teknetics Headphones:  Teknetics back to school promo

  • True Stereo
  • Swivel Earcups
  • Padded Earphones
  • Robust Construction
  • Utilizes 1/4 inch & 1/8 inch plugs

Digger Recovery Tool:

  • Tough carbon steel blade 7.5" L x 2" W
  • Total tool length 12"
  • Double-edged blade with 32 sharp cutting teeth to rip through roots and dirt Teknetics metal detector
  • No-slip blade guard
  • Comfortable rubber handle
  • Tough Cordura carry sheath for belt mount use 

Back-To-School Combo price ends August 18, 2018!  Get the package for only $499 with FREE SHIPPING!  Buy now using coupon code A1486.

Nugget of News Blog

Posted by: Denise AT 12:37 pm   |  Permalink   |  Email
Monday, July 30 2018

Places where gold naturally concentrates in an environment of streams and drainages are kgold paystreaknown as paystreaks. No matter if you are panning, sluicing, dry washing, or metal detecting, in many ways your success at gold prospecting comes down to locating these elusive natural pay streak concentrations. Keep in mind that most gold paystreak formations occur during times of flooding and that many factors affect how gold gets deposited. Perhaps the biggest factor is that gold is dense and is more than 19 times heavier than water. The denser an object, the more easily it will resist the flow of moving water. That means it takes a very strong and fast moving water flow to move along a nugget the size of a pea.

When deciding where to start sampling, it’s helpful if you think of a river or stream as a sluice box. Waterways obviously don’t have aluminum riffles and matting, however, they do have natural gold traps that do the same thing that a sluice will do— allow gold to settle out of gravels and be caught while the bulk of the sands continue downstream. Heavy material such as gold doesn’t get spread along evenly, it is most likely caught in certain areas. The downstream parts of inside bends in a stream are favorable places to look for pay streaks. Just how good depends on how sharp the bend in the stream actually is. Usually the sharper the bend, the better the pay streak. If a tributary is known to have coarse gold, look at the intersection of the tributary and the main channel.

Behind an obstruction (large boulder, an island, or an outcrop of bedrock) is another good place to look for a pay streak.  Boulders and other obstructions can create turbulence where ordinarily smooth flowing water turns into fast flowing whitewater. It is between the fast white water and the quiet dark water that gold drops out. The coarsest gold tends to be found on the outer parts of the pay streak, and the finer-sized gold is on the inner part of the pay streak. When you are working, if it seems as if the streak is petering out as you go toward the middle of the water flow because you are finding little gold, this region of the pay streak is often where the biggest number of nuggets are most likely to occur.

Once you know where paystreaks form, you might wonder if they are more likely found on bedrock or in gravels. They are nearly always found on bedrock or some sort of false bedrock. False bedrock might include caliche, a clay layer, or just a well-packed hard pan. You may just get lucky and hit something great with your first shovel of dirt, but more likely you’ll need to test a few different places. Even very experienced prospectors need to keep testing to find those hotspots and paystreaks. Good luck and keep sampling!

Posted by: Denise AT 10:17 pm   |  Permalink   |  Email
Friday, April 27 2018

A good rule of thumb that most prospectors agree on is to look for placer gold on bedrock and within crevices in the bedrock. This simple principle makes sense— placer gold is heavy and dense and therefore settles at the lowest point as it is pushed around by flowing water. However, gold isn’t always going to make it all the way down to true solid bedrock at the bottom of all gravels. Instead, in certain conditions, it will be found ABOVE bedrock. When these conditions exist, gold will collect on “false bedrock.” For example, a clay layer in streams can act like bedrock and yield more gold than the true bedrock below it. 

bedrock goldAnother situation where gold cannot make it to bedrock is where the streams and gullies have “caliche.” Caliche is a form of cemented gravel often found in desert areas. The gravel is deposited by water flows, just as it would be in any other stream. The difference is that the water contains dissolved calcium salts, and as the water dries up in the streambed, the calcium salts turn into calcium carbonate or calcite. This material gets deposited on the gravel a little at a time and eventually the calcite glues it all together into a solid mass. The solid mass then acts like false bedrock and any new gold flowing across it is stopped in its downward movement by the caliche.

Residual placer gold is formed near the source of the gold and doesn’t really have a chance to work its way downward. Hillside placers are residual placers that are sliding and making their way down the side of a hill into a stream drainage. Gold generally is distributed all through these types of gravels and is not concentrated in any one place. A hillside placer often will be located up above a stream, making it difficult to determine it from a bench placer. Old benches of river gravel can be good places to prospect because they are virgin ground, but because the river used to flow at this location, it’s highly likely that the best gold will be right on bedrock or in crevices of the bedrock. The best way to tell the difference between hillside and bench placers is the shape of the rocks in the gravel. If the gravels and rocks are well-rounded and smoothed, then it’s probably an old river bench. If the gravel is angular, pointy, and sharp, it’s probably a hillside placer that hasn’t yet made its way into a stream.

Another type of placer—the windblown placer— concentrates on the surface, just exactly the opposite of what you would find in a river or stream. The lightest materials such as sand and silt are blown away by the wind. Heavy materials like gold remain behind on the surface. These types of placers are marked by desert pavement, which is a concentration of small to medium-sized rocks that cover the surface and prevent continuing wind erosion. They occur in dry regions with flat terrain, and are often favorite locations of metal detectorists who find nice nuggets at shallow depths.

The next time you find yourself in an environment with well-washed river gravels, you know that the gold will most likely be on the bedrock. But if you find yourself in other types of environments, especially in the desert, consider the possibility that the best gold may actually collect ABOVE it.  Good luck!

Posted by: Denise AT 06:43 pm   |  Permalink   |  Email
Tuesday, February 06 2018

Historically, California has been known as the land of the big nuggets. After the Gold Rush began in 1849, gold nuggetsome of the biggest nuggets were discovered there because so many more people were out looking. For example, in 1854, miners working underground in the Morgan Mine at Carson Hill in Calaveras County pulled out a 195-pound mass of gold. It was 15 inches wide and four inches thick!  In 1859, a gigantic nugget was taken from ancient Tertiary river gravels on the slopes of Sawmill Peak near the West Branch of the Feather River and the small community of Dogtown. That nugget weighed 54 troy pounds. The spot where it was discovered was a hydraulic mine on the Willard claim that had a history of producing large nuggets in the past, including a 96-ounce nugget.

Plenty of stories abound from California, but plenty of big gold has come from other states as well. Colorado's biggest nugget weighed in at 156 ounces (13 troy pounds). It came from the Gold Flake mine located on Farmcomb Hill in Summit County, Colorado in 1877.  It's easy to see why Montana's nickname is the "Treasure State" since it has produced a few big nuggets, too. One weighed 53 ounces and was displayed at the Paris World Expoition of 1889. The largest in Montana was over 170 ounces and was dug at a depth of 12 feet in Snow Shoe Gulch on the Little Blackfoot River. Nevada's largest nugget was taken from the diggings of the Osceola District in 1878. It weighed 24 pounds (but eight pounds of that was quartz). The old Spanish miners found plenty of big gold in New Mexico, including one nugget in the late 1890s that weighed over 65 ounces.

buy gold nuggetsUnlike many Western states, the largest nugget in Alaska was found rather recently. In 1998, the Alaska Centennial Nugget, weighing 294 ounces, was mined along Swift Creek near the town of Ruby. This area is well known for its past production of large nuggets. A big nugget was also found in Anvil Creek near Nome which weighed 182 ounces.

North Carolina's claim to fame is the Reed Gold Mine located in Cabarrus County. It was the site of the first documented discovery of gold in 1799. For years, that 17 pound nugget was used as a doorstop because no one recognized what it was! At the time, it was worth roughly $4,000 (when the price of gold was $20.67 for an ounce). The Reed Mine actually produced a lot of big gold, including some weighing 28 pounds, 17 pounds, 16 pounds, and 13 pounds. Two different nuggets came from this area that weighed eight pounds each and another two nuggets were nine pounds each. Several more nuggets have been unearthed that weighed five pounds and less.

These examples of where large nuggets have been found are by no means exhaustive. A Google search will provide lots of fun stories about past and present finds across the United States. But no matter who has found what, the big question remains: Where do you hunt for big gold these days? Generally, big nuggets occur in places where rich gold-bearing fluids flow through the same pathways for a long period of time, allowing continued deposition of golgold nuggets for saled that lead to the formation of large pieces. These bigger pieces form where a change in geology allows a gold-bearing waterway to efficiently drop gold all in the same place. The same type of geology that produces rich pockets of ore with lots of visible gold are often the same areas where big nuggets are found. The really big nuggets are parts of pockets that have so much gold that they hold together as a single piece even after tumbling around in a stream.

The simple answer to where to hunt for big nuggets is to hunt where they have been found in the past. Past finds of big gold indicates these locations have the right geology for their formation. Big nuggets in a stream environment will work their way to bedrock very fast and stay put. They will often be lodged in deep crevices. Keep in mind that big nuggets are also worth more than their actual metal value. The fact they are so rare adds to their value. If you haven't found your big gold yet, keep looking! And if you can't wait to own your own shiny stuff, buy gold nuggets here.

Nugget of News Blog

Posted by: Denise AT 09:20 pm   |  Permalink   |  Email
Monday, January 29 2018
Make plans this spring to attend a Gold Prospectors Association of America (GPAA) Gold & Treasure Show! No matter your age or experience level, the expos offer something for everyone and provide the best opportunities to learn new skills, see product demos, and rub elbows with some of the most respected miners and metal detectorists in the business!

2018 gold show
Browse the show floor to find the latest and greatest gold mining and metal detecting equipment, attend free seminars, ask questions of the pros, and enter to win thousands of dollars in door prizes—metal detectors, sluice boxes, Gold Cube, and MORE! Also on the show floor are panning troughs for both kids and adults where you can learn new techniques— keep all the gold you find!

Saturday show hours 10 am - 5 pm and Sundays 10 am - 4 pm in these cities:

Tucson, AZ  February 17 & 18, 2018
Pomona, CA  February 24 & 25 
Ridgefield, WA March 24 & 25
Las Vegas, NV April 22 & 22
Boise, Idaho  May 5 & 6

Visit the GPAA website for details and to buy your $5 adult tickets online. Adult admission is $10 at the door; kids 12 and under are FREE and so are active duty military and veterans with ID.

Did you know... there is actually more gold to find today than the old-timers found way back in the 1800s gold rush era? Gold prospecting and treasure hunting has become a very popular and family oriented hobby, and these Gold and Treasure Shows are a great place to start in your search for that elusive shiny metal. See you there!

NOTE: Unfortunately, the ICMJ Gold Prospecting and Mining Summit usually held at the fairgrounds in Placerville, California has been cancelled for 2018. ICMJ is exploring other venues for April 2019.

Nugget of News Blog

Posted by: Denise AT 03:15 pm   |  Permalink   |  Email

Facebook
Pinterest
Twitter
Add to favorites

Nugget of News Blog